Cut down in it's prime . .

Following on from my post on the Cinelli and it's loose headset I am pleased to report that both my problems have been solved with the cutting down of the fork steerer.

For a very reasonable £12 Peason Cycles Sheen cut off the offending material and not only does the bike look finished now, the headset could be tightened correctly and there is no sign of the previous clicking or moving that I found.  I was so pleased with the price I rode the road bike there to collect the Cinelli and had that done the next day.

Full pictures of the bike to follow when I write it up properly in a long overdue "my bikes" section, but here's a photo of the now neat and cut back steerer.

The weight saving should have a few seconds off my commute right yeah . . 

Cinelli Single Speed - Cut Down Steerer

Where's your headset at . .

Commuting on the single speed cinelli has been a maintenance free experience this summer - partly thanks to the roasting sunshine the UK is currently enjoying, but after a recent downpour I felt that the headset had come a little loose.  After checking and setting the headset several times (instructions from Park Tool can be found in the link below) the problem got slightly better but wouldn't go away.

After some internet and book research a common cause was dirt or grit entering the assembly preventing it from tightening properly, probably during the rain.  Other than a failed or worn bearing there didn't seem to be many other candidates for the cause.  As the bike had been built for about 18 months, and probably covered 7/800km, dirt seemed the most likely candidate, and a strip down, clean and re-grease would remove most possibilities. 

The ever excellent Park Tool website has detailed instructions for removal, re-fitting and setting of thread less headsets, and their article can be found here:

http://www.parktool.com/blog/repair-help/threadless-headset-service

I started off by removing the front wheel and the front brake from the fork, slotting the handlebars into the bottle cage to keep them out of the way.

Cinelli Bootleg Mystic with fork and handlebars removed

Next I removed the headset bearings and cleaned all the relevant parts, working over a towel meant if any of the balls from the ball bearings made a break for it they couldn't get far, and they show up well against green.

Fork with front brake removed and both the upper and lower bearing races

Upon inspection the parts were in good condition but dirt was present, and the old grease was very dirty around the outer of the bearing races and where they contacted the frame and the fork.  The bearings themselves had cleaner grease on them and both they and the races were in perfect condition.  I used wet wipes (baby wipes) to clean the relevant parts, ideally I would have preferred to rinse and clean them in a solvent bath but this wasn't possible.  I also gave the bearing cups and the frame a good wipe over to remove any dirt or old grease.

Cleaned upper bearing parts

Cleaned headset cups and steerer tube

I then turned to my trusty tube of Finish Line Dupont Teflon bearing grease - this has been with me for many years and is excellent stuff for bearing services such as this one.  It is now almost done so I will be sourcing a new bottle when I next do some bike bits shopping, a link can be found below for Chainreaction Cycles.

http://www.chainreactioncycles.com/finish-line-teflon-grease/rp-prod980

This was applied to the internal races and the bearings themselves, with a small flat blade screwdriver used to push the grease into the hard to reach areas.  Once well greased the parts were snapped back together and the bearing assembly was ready to be re-insterted in to the bearing cups and the bike re-assembled.

Greased and re-assembled upper bearing parts

The bike was then put together and the process for tightning the headset from the Park Tools link followed.  The headset itself felt smooth and tight while turning, but here was still some play when locking the front brake and pushing back and forth.  This lead me to the conclusion that there isn't enough of a gap between the top of the fork steerer and the spacers/stem which the top cap presses against.  

This enables me to hit two birds with one stone (has anyone ever actually done that?) as the steerer has needed cutting down for a while.  Much to my good buddy Russ T's disgust I have previously shied away from cutting down fork steerers for two very good reasons; 1 - I might sell the bike, 2 - I might mess it up and cut off too much.  However, aesthetically I do hate that bit of steerer and spacers sticking out the top and now was the time to get rid.  So this is a job for the LBS (Local Bike Shop).  While I now do most jobs myself I've always believed you should support your local shop, and days like these are proof why everyone should.  

My local shop is Pearson Cycles in East Sheen, I ride past there regularly going to Richmond Park or further afield and aside from some very nice machines and tasty coffee, they have very helpful staff and excellent mechanics.  I have previously stopped in to borrow a torque wrench for a slipped saddle, and had an errant wheel trued and their service has been top notch.  

So the bike has been dropped off and I eagerly await her return, both to see if the headset is fixed, and to see what she looks like without that ugly bit of steerer sticking out the top.   

Peasrson Cycles can be found online here, and in addition to being an excellent bike shop, they are also the oldest in the world so well worth a look:

http://www.pearsoncycles.co.uk

XC Racer - BB30 Bolt Replacement

During the Whyte 20-CS xc racer build I mentioned that the self extracting bolt looked like it might be damaged and this did indeed turn out to be the case.  When I started to tighten the cranks up to the specified torque the effort dropped off suddenly and it was clear the bolt had pulled through the crank arm. 

The bolt in question can be seen in the diagram below, which is taken from the FSA BB30 Installation manual and can be found at the link below:

https://www.bike-components.de/bedienungsanleitungen/2011/fsa/atb/mtb_bb30_detailed_instructions.pdf

Exploded diagram of the cranks from the FSA Installation Instructions

The self extracting bolt, or BB30 Crank Bolt as FSA refer to it in the figure above, is top hat in section, and the brim of the top hat was the area that had failed.  Usually this type of bolt is steel but this FSA version is a very lightweight alloy, something like ZAMAK, which is light and dimensionally accurate as a material but has a high air content and prone to crumbling, which had happened in this instance.  The Bolt has a 10mm Allen head and the top hat section contacts the crank arm and drives it along the splines of the spindle as the bolt is rotated.  This part was most likely over-torqued causing the in-expensive bolt to fail rather than the much more expensive crank arm.

The old bolt can be seen below on the left next to the new replacement bolt.

The replacement bolt was bought from Triton Cycles, link below.

http://www.tritoncycles.co.uk/components-c9/crank-spares-c186/fsa-bb30-crank-bolt-p5253

XC Racer - the Reveal

The bike is finished, well a bike is rarely ever finished so more accurately, the build is finished.

Jobs left to do are tune the gears, setting the air in the forks and re-mounting the tyres tubeless.  Once those tasks are done I will get out and report back on the ride, but for now here are some pictures and the final spec.

I've always preferred a smaller bike so plenty of seatpin is great for me

Whyte did a brilliant job with the colour scheme - love red white and black on a bike

This shot just makes me want to jump on and hit the dirt

The bars, grips, stem and XX levers go well with the frame and forks

The fork decals are definitely more orange but it works

They were totally budget driven - but the cranks suit the bike well

I would have preferred SRAM but as ever the Shimano kit fits well and works perfectly

Rocket Ron - the "do it all" UK tyre choice

Big beefy bottom bracket area and BB30 crank bearings

From a different era - but the Bontrager Race Lite wheels look great

Love the XX brakes - look the business and super light

Not usually a fan of factory finishing kit but Whyte have done a great job on the stem

So far it looks super fast, I'm really pleased with it and it definitely looks the business - which passes my first test criteria.  From a few pedals around the car park the brakes feel super grabby and the ride is really nimble - I can't wait to show it some trails and see how she performs on some proper single track.  

Build Spec

Frame: 2012 Whyte 20-CS Full Carbon Uni-directional Multi Monoque, full carbon dropouts

Forks: RockShox SID RLT, 100mm Travel, Remote Poploc

Bars: Race Face XC Low Rise

Stem: Whyte Custom70mm

Headset: FSA Integrated, Orbit ZS Plus, 1 1/8" - 1 1/2" Sealed Cartridge Bearing

Grips: Prologo Feather Lock-on White

Front Brake Lever: SRAM XX

Front Caliper: SRAM XX

Front Disc: Avid HSX 180mm

Rear Brake Lever: SRAM XX

Rear Caliper: SRAM XX

Rear Disc: Avid HSX 160mm

Shifters: Shimano SLX 3 x 9

Cables: Clarks Sealed

Front Mech: Shimano XT

Rear Mech: Shimano XT

Saddle: Selle Italia X1

Seat Post: Whyte Custom 2014 Alloy, 27.2mm x 400mm, 2 bolt clamp

Seat Post Clamp: Whyte

Cranks: FSA Afterburner BB30 175

Chainring(s): FSA Afterburner BB30

Chain: KMC X10SL-Gold

Cassette: Shimano SLX

Pedals: Shimano M-520 SPD

Bottom Bracket: FSA Afterburner BB30

Wheelset: Bontrager Race Lite DT Swiss Onyx Hubs

Tubes: Continental

Tyres: Schwalbe Rocket Ron Evo 

Accessories: 

None (yet)

Weight: sub 11kg (est)

Project XC Racer - Cable Routing

Building the Whyte 20-CS went pretty easily, but the one thing I tangled myself up a bit with was the gear cable routing.  The first thing to stump me was the cable brackets themselves.  As fitted to the frame when I received it (admittedly second hand) they have a wider diameter on the RHS (Right Hand Side) of the bike (LHS as viewed from the front of the bike).  The second was which side the cables should run, the convention would be the rear deraillieur cable down the left to allow a nice smooth curve to the cable from the right hand shifter, and vice versa for the front dérailleur - but at first look this wouldn't work.  As I bought the frame used, I decided to crack on and try to figure these things out for myself.

My first thought was that the wider diameter clamp was for the rear brake as the hydraulic line has a wider diameter, however I quickly ruled this out as the rear brake has it's own dedicated run underneath the down tube, and with the rear calliper mount between the chainstay it couldn't run any other way.  My final thought on the bracket was that it had been designed this way to allow a 1 x 10 set up with the vacated clamp for the front dérailleur used to run the hydraulic line for a dropper post. 

For the gear cable routing, the conventional routing made the curve around the seat tube for the front dérailleur very tight.  I had researched lots of images, as well as the Whyte 2012 catalogue to see what other bikes were built with.  Though there aren't too many Whyte 20-C's out there, I found several examples but even across the range in the catalogue from Whyte, there wasn't a consistent majority for any one set up.

What I found to suit the frame best was running the front deraillieur cable down the RHS of the bike and the rear deraillier down the LHS with a crossover between the second and third clamps and both cables running round the RHS of the seatpost.  This can be seen in the image from the Whyte 2012 20-C page on the Whyte website.

http://whyte.bike/2012/bike_page.php?ModNo=W-1-008-12

Whyte 20-CS Cable Routing

Whyte 20-C Cable Routing

Conventional Routing but with both cables on the RHS of the seat tube

Whyte 20-CS Cable Routing

Whyte 20-C Routing and Preferred Option

For now I am going to go with the routing from the 20-C on the Whyte website, but will see if I can contact Whyte or one of their distributors to see if they can help.

XC Racer Part IV - the Build

With all the bits in stock and some optional extras added all was ready for the build.  First in was the seatpost so that the frame could then be mounted on my workstand.  I'm a big fan of Park Tools and Topeak, and while I looked at and tried several workstands, the Topeak PrepStand™ Elite was the model I chose, it's well built, easy to use, super strong and works well on rough surfaces.

Topeak PrepStand™ Elite

http://www.topeak.com/products/Repair-Stands/prepstandelite

Once mounted I could get the crankset installed, this being my first experience of BB30 I did my homework, I'd bought my crankset on eBay so found the installation instructions online.  All was simple enough, particularly as the bearings were already pressed into the frame so the remaining installation was similar to Shimano Hollowtech II and Sram Mega Exo external type bearings.

If you are looking for instructions for installation those for the FSA Afterburner BB30 cranks can be found here:

https://www.bike-components.de/bedienungsanleitungen/2011/fsa/atb/mtb_bb30_detailed_instructions.pdf

During installation I noted that the captive nut that fixes the left hand crank arm onto the spindle looked worn or damaged with much of the flat "top had" section crumbled away so only loosely tightened this up.  I continued work as I would not be riding the bike straight away but made a note to check this when I tightened up the crankset to the correct torque setting.

Frame mounted in the workstand

BB30 Afterburner Cranks Fitted

Please excuse the glamorous location - with a very young baby you take your chances to make workshop space and time where you can!

Next I fitted the forks, stem and handlebars - fortunately the headset bearings were also already pressed in so this was simply a case of fitting enough spacers and tightening everything up.  I fitted the spacers under the stem for now, I'll sort the geometry once the bike is finished.  Next to go on were the brakes, my original plan was to run a 160mm disc up front and a 140mm on the rear to keep things lightweight and as I would expect that to be enough power with the XX brakes.  After checking the rear brake mount is 160mm minimum, and as I only had one of each size of disc, I went for 180mm front with a 20mm caliper spacer and 160mm rear.

Front brake lever fitted - grey marks on the bars wipe off

Rear brake lever, front shifter and Poplock Control

Front Brake with 20mm calliper spacer and 180mm disc

Rear brake with calliper mount inside chain and seat stay and 160mm disc

While fitting the brake discs I also prepared the wheels by fitting the cassette and the tyres.  Once complete I will be running the tyres tubeless but to get the bike rolling and help seat the tubeless tyres I removed the tubeless valves and fitted the Schwalbe Rocket Ron's with a pair of Continental tubes and inflated them to the maximum 50psi to fit the bead tightly to the rim, this will help seat the tyres when I fit them tubeless.

Next came the gears, I picked up a set of Clark's sealed inner and outer cables, mounted the shifters and rear dérailleur and ran into my second concern.  The SLX front dérailleur I had in stock from my old groupset was a low mount type, and the form of the seat tube where it meets the bottom bracket area of the frame is much wider than on a conventional tubed frame and this type of dérailleur simply won't fit.

Some time on eBay showed that there wasn't much to be saved going used and with an XT rear mech already installed I managed to find an XT front mech for £17.25 from High Altitude Bikes.

Shimano FD-M771 Front Derailieur

http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=360969468350

The new front mech fitted very easily, following the installation instructions for the torque on the clamp bolt, aligning the cage to be parallel to the chainrings and ensuring that the outer cage plate was 1mm above the big chainring teeth.

Front Dérailleur Fitted

Rear Dérailleur

With the deraillieurs fitted it was time to run the cables, fit the handlebar grips, set all the handlebar controls to the correct angle and spacing.  For angle the general consensus is that the line of your forearm should line through the brake levers when viewed from the side.  For the grips, shifters and PopLock lever I followed the manufacturers recommendations and my own preference for look.

Last but not least were the pedals which are Shimano entry level SPD and get some pictures of the finished result in all it's glory.

I'll save those for a final reveal with all the build spec.

More Single Speed Commuting . .

So it's been a while since I posted about life commuting and an office move for my company meant that direct comparison between my first few commutes with gears was not possible.  We are now settled in the new office and I've been doing two or three commutes a day, which I'm really enjoying, particularly as I'm starting to get some reasonable fitness.  The even newer commute is just over 26km over almost the same route, which is pretty flat but largely free flowing and mostly traffic free.  

My previous goal was to get the single speed time down to the original time that I did on the geared road bike, which I aim to do again for this new commute, but I may have made a rod for my own back.  After several rides on the single speed I rode the road bike last Wednesday in preparation for heading up to Yorkshire to watch Le Tour and have a crack at Stage 1.  My best on the single speed on the new route was 58:36 as can be seen in the Strava link below:

http://www.strava.com/activities/163438601

The time recorded on the road bike was 52:53 as can be seen here:

http://www.strava.com/activities/160996301

The single speed is real hard to keep at high speed but I all too often ease off and coast which is probably why a lot of pro riders incorporate some fixed single speed riding into their training, but for safety I run the single speed with a freewheel as London presents a lot of hazards.  So I will really have to push myself to try and get that time down - and then see if I can go quicker again on the geared road bike.

This is going to wreck my legs, but with a twelve week old baby I can't join a club, race or train specifically so this is the best way to get some sport and have a target to focus on.  

I'll check back in on this in a month with my success/failure* . . 

*delete as applicable